Reviews : Tamiya Hawker Sea Harrier

This is my 6th Airplane build since restarting modeling after over 30 years. I'd heard great hype about Tamiya kits being very accurate, nicely detailed and that they go together well, and so was excited to find one with an unusually low price. The low price has its reasons; the parts come from a mold manufactured in 1982 (32 years old), there were a lot of parts that required sanding / trimming of flash before fitting and painting. The Engine cover panel when placed into location is sloppy leaving a gap all around. The option is there to leave this loose to remove and display the Rolls Royce Pegasus engine, but unless you're going to add extra details to enhance it, save yourself the trouble of painting it and secure the engine cover panel. But, you will need to fill the gaps before painting. The cockpit interior is minimal- a very basic tub with a seat, a joy-stick, a pilot and a instrument panel indicated by a decal. It doesn't include side wall details, or console switches and handles. Again, you could enhance the interior with an after-market resin and etched brass kit. The fit of the wings to the fuselage could be set at a slightly shallower angle compared to the actual plane. The reason I say this, is when you assemble all the wheels, including the two wing tip stabilizer wheels, you'll find that the wing tip wheels are off the ground and so the plane will tip to one side and rest on one of them. A simple fix for this, and one that I employed, was to sand around 1/16th of an inch off the bottom of the fuselage wheels which then lowered the plane and the wing tip wheels sat nicely on the ground. When fitting the front cockpit window, the profile of mine was wider than the profile of the fuselage and therefore, it overhung on both sides. I tried to flex the sides in and hold them in place until the glue bond retained the position. But, whilst doing that, stress crazing appeared and so I stopped. When it comes to decaling, these are thicker and glossier than the more recent decals and therefore, if you want them to look painted on, ensure a good coat of gloss varnish followed by 2 good finishing coats. A few of the decals also cracked during application and discovered that they were reacting to the decal application solution. To overcome that, I simply diluted the solution with water. The Air-Intake nozzles are smooth and do not have molded in air flaps that go around the periphery of them. These are features that stand out on a Harrier during its resting position as they drop inwards leaving open windows. Again, this would require either surgery to the existing nozzles to replicate them, or the purchase of after-market resin air intake nozzles. A simpler remedy might be to create a stencil and paint these windows onto the plane? When fitting the Air Intake Nozzles to the fuselage you'll find that their profile doesn't match with the fuselage and require filling and sanding. The plane does come with 3 options of weapons load, I went for four 1,000lb bombs, two on each wing, couple with AIM 9L Sidewinder missiles. The two Aden guns are common to all options. Overall; for the low price, you can't grumble at what you're getting in the kit. I did enjoy building it, despite the nuances, and it does look good when made. My model was built straight from the box with no added extras. Beginner modelers will need patience, but they will be satisfied for being patient. Seasoned modelers will no doubt use the money saved on this low priced kit to purchase the enhancements that are available for it.

This is an early(ish) Tamiya molding, 1982 to be exact. The part number is low, which is refreshing (not to have to craft those difficult Harrier landing gear). As with most Tamiya kits, there are many advantages. The engine and cockpit have nice pegs to help in setting that I don't often see in kits of this price range. Fuselage fits well, with some sanding and re-cutting panel lines. The panel line are raised, which makes it harder to add finishing touches (recessed panel lines are much easier). This is the earlier Harrier model, before McDonnell Douglas redesigned the larger wings with carbon fiber. There is limited cockpit detail, but I was able to really put some time into the pilot to make him look good with shading and lots of detail. My one big problem is the lack of intakes for the engine on each side. All Harriers show a lot of wear on these small intakes, and that provides the opportunity for authentic detailing. This model does not provide that. For the price range though, you can't go wrong getting a Tamiya model ay such a good discount. Happy modeling!

This is definitely a good kit, but it is starting to show its age in some ways. It primarily has raised panel lines, which more modern Tamiya kits don't have. The lack of molded cockpit detail is annoying, but the decal instrument panel is good enough. The pilot figure is definitely not usable, it's more an amorphous blob than anything else, but that doesn't matter to me since normally I don't put in pilot figures. The fit issues are no worse than any other jet kit. It's definitely the best 1/48 aircraft kit in it's price range, but I wouldn't necessarily recommend it to beginners due to the Kit's age.

I have built tons of Tamiya kits and have never had an issue with them. The instructions are always clear and easy to follow and usually provide tips that can help improve the kit. There was no flash on the parts and everything fit together like it should. The cockpit detailing was ok. The instrument panel was a decal, and there were some minor details on the walls. An ambitious modeler should be able to improve on the kit and super detail everything to really set it apart from other planes. I'd recommend this kit to anyone as it went together without any problems and creates a pretty nice plane when finished.

This is an old mold, and it shows. My example was covered completely in flash, so clean up is tedious -- and necessary! It is a raised panel line kit, which is not an immediate negative for me as the price is exceptional. But Tamiya has come a long, long way in the likely 40 years since the molds were cut for this plane, and it's not a fall-together kit, nor is it overly detailed. With a lot of clean up and careful work, an acceptable shelf sitting model may be achieved.

As Tamiya kits go, this is below average. Raised panel lines, fit issues around the wing roots and engine access hatch. The cockpit detail is practically none existent. There are some recessed details that are VERY faint...mostly around the intakes. The exhausts don't rotate like they're suppose to. Do I recommend this kit? Sure, why not! However, there are better kits out there than this one.

For the price of this kit it’s worth it. Several issues due to the age of the tooling but nothing major. Good kit for beginners to move on to more advanced stages, the only real issue is the seam down the fuselage which isn’t that major. A couple of minor fit issues and please put the lower wing paint and decals in before the weapons otherwise you be using some language.

This is a generally good kit, with fit issues around wing roots. The fit of this kit is overall pretty good. The kit is a representation of the first Harriers to go into service, FRS.1 standing for Fighter/Reconnaissance/Strike Mark 1.

Overall a well made kit. Could use some details in the wheel well and cockpit area and the panel lines weren’t too “realistic” I enjoyed building it and adding it to my collection. Plus it didn’t cost too much.

Good kit.good price.very sturdy.engine nozzle thrusters turn .OTHER options also.Highly accurate

Nice kit, great subject and good details, a great addition to my collection.

Happy with it. It was fun to build and easy to asemble and paint and decal